Pest Control

The RobberGards™ is an ingenious device to fool wasps and robber bees and stop them from getting into the colony.

These unwanted visitors are guided to potential food in the hive largely by sense of smell.

They go straight to the vent holes at bottom of the RobberGards™and try to get in, without realizing the entrance is at the top.

These intruders very soon give up and go looking for food elsewhere.

The bees learn within 24 hours how to access their own hive and it doesn’t stop them carrying out all their normal duties.

Eye Screws to secure the RobberGards to brood box can be PURCHASED HERE

Click Here to see how to fit them to 4 different types of floors

See what “A Kiwi Beeman” thinks about RobberGards Here

Varroa mite re-invasion

This is a huge issue in Autumn and it is believed to be the largest contributor to colony losses.

The varroa mite re-invasion is a result of visits from robber bees and/or from social bee visits.

This was highlighted at the 2021 NZ Bee Conference by an excellent study done by Dr Dennis vanEngelsdorp and shown in this video:-

https://youtu.be/PvWZjwUbLfA?t=1671 

Watch content from 27 min to 33 min. (Remember the study was done in Autumn in USA.)

The RobberGard is especially designed to deter these robber bees and social bees.

Some of the features and benefits of the RobberGards:-

1. The registered design is made from high quality stainless steel to withstand the corrosive elements outside and last for a very long time, virtually indefinitely.
2. Deters robber bees that want to steal the food supplies inside.
3. Deters social bees from other colonies that want to come and have a look and will mostly spread varroa mites.
4. Deters wasps from robbing food from the colony.
5. Stops mice getting in and damaging the honey combs.
6. Helps to control spread of AFB disease. If a colony gets AFB and has this robber guard, it is far less likely to get robbed out and spread the disease, before the beekeeper finds it and burns it.
7. Allows a lot more ventilation over winter (in hives with solid bases) to reduce condensation in the hives which is detrimental to the health of the colony.
8. Easy to block up with foam rubber if the beehive has to be shifted. The bees can still get lots of ventilation through the robber guard vent holes.
9. Very easy to mount, switch entries or remove with the use of the stainless steel eye screws supplied by Beequip NZ.
10. Has a summer position or rotate 180 degrees for the robbing season and winter. The entrance is just 25mm wide in this setting.
11. One of the 3 sizes will fit virtually every type of beehive base (floor) that is commonly used in NZ.

These can also be used as:

• Mouse guards
• Wasp Guards
• Anti-wasp screens
• Anti-robbing screens
• Robber Guards

Units packed in a carton:

RobberGard 153 - 200 / Carton
RobberGard 225 - 150 / Carton
RobberGard 360 - 100 / Carton

Pricing is per individual unit.

Got a problem with ants in your Beehive?

Ants love honey and some ants are omnivorous so eat the brood as well! A beehive is a perfect food warehouse for them. Ants don't sleep and can forage 24/7 if the temperature is over 10 degrees celsius. Bees have very little defence against Ants and they can cause far more damage than beekeepers realise.

These stainless steel feet are designed to create a barrier against ants entering your hive. Simply attach them to your beehive base/floor, fill the tray with vegetable oil and the ants are stopped immediately!

The feet feature a rain cover for the tray to stop water getting in. This is important because otherwise water will sink to bottom of tray and the oil spills out the top. Then on a hot day the water evaporates and disappears.

The feet come in sets of 4 with two types available: -

Threaded stud mount
This type is designed to be fitted by drilling four 10mm diameter holes of equal depth in your base (40mm) and then inserting the stud. With this method they can be easily added or removed. Drill 9.5mm diameter holes if you want the studs to be a firm fit. Tap the studs into the holes gently with a block of wood, before the tray is fitted. Technoset bases: - Remove the plastic feet from the base and there is a hole already in the base to suit the stud. Add some thin wall tube to the stud if a tight fit is required.

Flange Mount
This type has a flat plate on the end with screw holes and can be attached to a flat surface on the bottom of a floor with 4 screws. This is a more permanent mounting solution. 

Tip. Ants will walk up grass or weeds to access a beehive. Keep all weeds or grass clear of the hive. Second hand carpet is usually available free in most places and is great weed matting. Mounting the base on a pallet is also very helpful.

Wasps are significant pests for bees and can be very devastating in some areas. Our answer to this problem is to remove the pest without the use of harmful chemicals and without endangering the bees and the environment. To bait, simply place a small piece of raw fish in the trap. It is best if it is starting to go off, and is giving off a strong odour!

Or for best results - use our Wasp Lure which you can find here. Check out the pictures from a customer who had used both - these results were only after 3 days!

Wasps enter the internal cone and are unable to escape.

This trap is a great lure for wasps and will greatly help to keep them away from beehives or your house in the Autumn.

Tip! Don't forget to use these traps early in Spring to catch all the Queen Wasps when they come out of hibernation and are looking for protein when they establish their new nests.

High quality stainless steel construction.
Made in Europe.

Dimensions: 340mm diameter, 350mm high. Weight: 1 kg

Anti-wasp plate for Technoset floors.

This black plastic sheet slots perfectly on to a Technoset floor. It reduces the entrance to a small square hole right close to the cluster during winter. This stops wasps as they don't like the dark tunnel from the front entrance to the inside entrance. It also makes it easier for the bees to defend themselves.

Scientifically formulated and non-toxic. Attractive to wasps, not bees.

A specially formulated, non-toxic liquid lure which is attractive to Common and German wasps, but NOT to bees or Paper wasps. For use in the refillable NoPests® Wasp Dome Traps or our Stainless Steel Technoset Wasp trap. Available in 1L & 5L packs.

1. Unlock the Wasp Dome Trap, pour in 250ml of NoPests® Wasp Lure.
2. Lock Wasp Dome Trap lid to closed position.
3. Locate trap in direct sunlight in areas where wasps frequent, using hanging cord provided.
4. Inspect the dome trap regularly and remove dead insects.
5. Replace lure monthly, or when levels drop due to evaporation.
6. If the dome trap is full and there is no free liquid, remove contents and rinse with clean water before refilling with NoPests® Wasp Lure.

Easy set and refillable. Attractive to wasps, not bees.

A reusable wasp trapping system for use with NoPests® Wasp Lure (sold separately). Highly effective with the capacity to capture hundreds of wasps. When full, empty contents in trash and refill again with NoPests® Wasp Lure. Contains 1 Wasp Dome Trap (yellow base with clear lid) and 1 suspension string.

1. Unlock the Wasp Dome Trap, pour in 250ml of NoPests® Wasp Lure.
2. Lock Wasp Dome Trap lid to the closed position.
3. Locate trap in direct sunlight in areas where wasps frequent, using hanging cord provided.
4. Inspect the dome trap regularly and remove dead insects.
5. Replace lure monthly, or when levels drop due to evaporation.
6. If the dome trap is full and there is no free liquid, remove contents and rinse with clean water before refilling with NoPests® Wasp Lure. Ensure no Lure is spilt on the outside of the dome trap.

Ant Control Spray - X-It Ant 225ml.